How to remove stripped car battery hold down clamps?
Q. My husband is trying to change the battery in my Ford Escape. The negative hold down clamp bolt is stripped, so the wrench just turns around it doing nothing. Any suggestions on how to get it off?
Asked by abigail_rdh - Thu Jul 15 20:38:12 2010 - - 3 Answers - 0 Comments
Q. My husband is trying to change the battery in my Ford Escape. The negative hold down clamp bolt is stripped, so the wrench just turns around it doing nothing. Any suggestions on how to get it off?
Asked by abigail_rdh - Thu Jul 15 20:38:12 2010 - - 3 Answers - 0 Comments
How to remove stripped hex headed bolt on power steering pump pulley?
Q. Is it possible to remove a stripped hex headed bolt that connects the pulley to the power steering pump? Well I don't think vise grips are going to work because the bolt is about flush with the pulley. I wouldn't even be able to budge it even if I could, I was using a piece of pipe as a cheater bar to even get it out this far. I am just wondering if it even has some loctite on it.
Asked by Chris - Sun Mar 15 20:02:09 2009 - - 5 Answers - 0 Comments
A. You've got a few choices if you already have it out of the car. You can purchase the extractor tool and attempt the repair on your own. Or you can take it to a reputable local mechanic and let them remove it for you. If it's still in the car for some reason or other, just make sure you center punch the hex nut as close as possible before you drill it with a hardened carbide bit or a quality bit for hardened steel. Good Luck to you
Answered by kevusaborn - Sun Mar 15 20:22:10 2009
Q. Is it possible to remove a stripped hex headed bolt that connects the pulley to the power steering pump? Well I don't think vise grips are going to work because the bolt is about flush with the pulley. I wouldn't even be able to budge it even if I could, I was using a piece of pipe as a cheater bar to even get it out this far. I am just wondering if it even has some loctite on it.
Asked by Chris - Sun Mar 15 20:02:09 2009 - - 5 Answers - 0 Comments
A. You've got a few choices if you already have it out of the car. You can purchase the extractor tool and attempt the repair on your own. Or you can take it to a reputable local mechanic and let them remove it for you. If it's still in the car for some reason or other, just make sure you center punch the hex nut as close as possible before you drill it with a hardened carbide bit or a quality bit for hardened steel. Good Luck to you
Answered by kevusaborn - Sun Mar 15 20:22:10 2009
How do you remove stripped screws in Guitar hero controller?
Q. I have a Guitar Hero World Tour controller that has the yellow fret button not working. It is past the 90 day warranty and so I can save myself $50, I am attempting to open the fret board up and readjust the circuit board into position. A few of the screws were stripped when I went to remove them and I have no clue as of how to remove them. Please help if possible. I am on a budget and cannot buy items so I am looking for a household remedy.
Asked by theone3150 - Wed Mar 10 09:55:12 2010 - - 3 Answers - 0 Comments
A. Call a hardware store. There is a tool that will removed the striped screws. If the hardware store does not have it try Sears and if they don't have it email me as there may be a way I can find one for you.
Answered by Mommiedearest - Wed Mar 10 10:07:48 2010
Q. I have a Guitar Hero World Tour controller that has the yellow fret button not working. It is past the 90 day warranty and so I can save myself $50, I am attempting to open the fret board up and readjust the circuit board into position. A few of the screws were stripped when I went to remove them and I have no clue as of how to remove them. Please help if possible. I am on a budget and cannot buy items so I am looking for a household remedy.
Asked by theone3150 - Wed Mar 10 09:55:12 2010 - - 3 Answers - 0 Comments
A. Call a hardware store. There is a tool that will removed the striped screws. If the hardware store does not have it try Sears and if they don't have it email me as there may be a way I can find one for you.
Answered by Mommiedearest - Wed Mar 10 10:07:48 2010
How would you remove a stripped hex screw from a motorcycle?
Q. I have one more bolt to remove from my rotor cover I'm trying to remove. The bolt is stripped and I'm having trouble remove it, what's the best and easiest way to remove it?
Asked by magix3d - Tue Jun 23 23:57:16 2009 - - 5 Answers - 0 Comments
A. If you can get at the head, slot it with a Dremel and use a good screwdriver or impact driver to loosen it. Or, you may be able to drill through the head and get the cover off. Once there is no tension on the screw, the remaining bit will probably back out easily.
Answered by Buster Brown - Wed Jun 24 00:18:39 2009
Q. I have one more bolt to remove from my rotor cover I'm trying to remove. The bolt is stripped and I'm having trouble remove it, what's the best and easiest way to remove it?
Asked by magix3d - Tue Jun 23 23:57:16 2009 - - 5 Answers - 0 Comments
A. If you can get at the head, slot it with a Dremel and use a good screwdriver or impact driver to loosen it. Or, you may be able to drill through the head and get the cover off. Once there is no tension on the screw, the remaining bit will probably back out easily.
Answered by Buster Brown - Wed Jun 24 00:18:39 2009
How can I get a stripped bolt on my car tire out?
Q. I got a flat and one of the bolts is stripped. I neen help on what to do. I can't drive it to a shop because it's riding on the rim. Please help!
Asked by prettylady - Thu Nov 1 18:30:44 2007 - - 6 Answers - 0 Comments
A. Is it the lug or the nut that is stripped? If it's the nut that is rounded off, then find a socket that is a little bit smaller and beat it on with a hammer. If it's the lug itself, a cutting torch is the easy way to go on that. I doubt that you have one though. You could use a hammer and chisel to split the nut. If you live in the Kansas City area, let me know and I could come help you out. Good Luck
Answered by MAD MEL - Thu Nov 1 18:45:57 2007
Q. I got a flat and one of the bolts is stripped. I neen help on what to do. I can't drive it to a shop because it's riding on the rim. Please help!
Asked by prettylady - Thu Nov 1 18:30:44 2007 - - 6 Answers - 0 Comments
A. Is it the lug or the nut that is stripped? If it's the nut that is rounded off, then find a socket that is a little bit smaller and beat it on with a hammer. If it's the lug itself, a cutting torch is the easy way to go on that. I doubt that you have one though. You could use a hammer and chisel to split the nut. If you live in the Kansas City area, let me know and I could come help you out. Good Luck
Answered by MAD MEL - Thu Nov 1 18:45:57 2007
How can I fix the threads that are stripped on an aluminum intake manifold?
Q. The threads are stripped out on my intake manifold . I need to fix it so I can thread a new bolt in it.
Asked by Joey C - Sat Jun 12 13:23:02 2010 - - 7 Answers - 0 Comments
Q. The threads are stripped out on my intake manifold . I need to fix it so I can thread a new bolt in it.
Asked by Joey C - Sat Jun 12 13:23:02 2010 - - 7 Answers - 0 Comments
Can anyone tell me how to remove a stripped screw from a winshield wiper?
Q. After trying to replace my windshield wipers, the screw had been in the wiper for so long, it was hard getting it out. After trying on numerous occasions, it has become stripped.
Asked by Ms. Personality - Sun Feb 24 18:35:30 2008 - - 2 Answers - 0 Comments
A. Go to Home Depot, Lowe's, or whatever your nearest hardware store equivalent is, and go straight to its tool section. What you are looking for is called a Screw-Extractor. They make various sizes, so get the one that looks closest to the screw you've got. They can usually be found near the drill bits. There will be instructions on the package, but you can also ask one of the clerks how it works.
Answered by LongHaul - Sun Feb 24 18:51:12 2008
Q. After trying to replace my windshield wipers, the screw had been in the wiper for so long, it was hard getting it out. After trying on numerous occasions, it has become stripped.
Asked by Ms. Personality - Sun Feb 24 18:35:30 2008 - - 2 Answers - 0 Comments
A. Go to Home Depot, Lowe's, or whatever your nearest hardware store equivalent is, and go straight to its tool section. What you are looking for is called a Screw-Extractor. They make various sizes, so get the one that looks closest to the screw you've got. They can usually be found near the drill bits. There will be instructions on the package, but you can also ask one of the clerks how it works.
Answered by LongHaul - Sun Feb 24 18:51:12 2008
How do you feel of Miss California being stripped of her title?
Q. Do you think she was stripped of her title because she spoke out against same-sex marriage? Do you feel it was fair?
Asked by This Path I Take Today - Wed Jun 10 21:49:47 2009 - - 2 Answers - 0 Comments
A. Of course she was fired because of her supposed "controversial" (yeah right) answer. She even said she cooperated with them and it came as a surprise. I find it odd that journalists originally and continue to portray that her answer was somehow some big story. President Obama gave the same answer ffs. The fact that this even became a story at all reveals just how amazingly bias and tabloid the pc media has become. I hope she sues, it's obvious the committee was against her and were actively searching for any way to part ways.
Answered by super g - Thu Jun 11 01:58:51 2009
Q. Do you think she was stripped of her title because she spoke out against same-sex marriage? Do you feel it was fair?
Asked by This Path I Take Today - Wed Jun 10 21:49:47 2009 - - 2 Answers - 0 Comments
A. Of course she was fired because of her supposed "controversial" (yeah right) answer. She even said she cooperated with them and it came as a surprise. I find it odd that journalists originally and continue to portray that her answer was somehow some big story. President Obama gave the same answer ffs. The fact that this even became a story at all reveals just how amazingly bias and tabloid the pc media has become. I hope she sues, it's obvious the committee was against her and were actively searching for any way to part ways.
Answered by super g - Thu Jun 11 01:58:51 2009
What are the physical effects of an electron being stripped from an atom?
Q. While I know that they sometimes release photons and thermal energy, are there any other effects that are directly caused by the electron leaving/being stripped from the atom?
Asked by narinonein - Tue Dec 2 09:06:44 2008 - - 1 Answers - 0 Comments
A. The atom has to absorb a photon in order to release an electron. So the end products are: One fewer photons of that energy in the universe. A positive ion An electron
Answered by ( )Mistress Bekki - Tue Dec 2 09:10:35 2008
Q. While I know that they sometimes release photons and thermal energy, are there any other effects that are directly caused by the electron leaving/being stripped from the atom?
Asked by narinonein - Tue Dec 2 09:06:44 2008 - - 1 Answers - 0 Comments
A. The atom has to absorb a photon in order to release an electron. So the end products are: One fewer photons of that energy in the universe. A positive ion An electron
Answered by ( )Mistress Bekki - Tue Dec 2 09:10:35 2008
How much does it cost to professionally get hair dye stripped out of your hair?
Q. I recently dyed my hair black and its naturally dirty blond. I wanna get it stripped but last time I did it myself it came out like 4 colors. Does anybody know about how much it cost for them to do it at a hair salon?
Asked by Lindsey J - Sun Nov 18 23:33:04 2007 - - 3 Answers - 0 Comments
A. This is corrective haircolor and it is the most expensive salon color service, due to the amount of time involved and the amount of products needed to fix the problem. This is the primary reason why you should have a hairdresser color your hair, so it doesn't come out in 4 different colors. It would cost you less to have that done vs corrective. Most hairdressers charge by the hour for corrective, because it can take a lot of time and products. If a hairdresser normally can make $75 - $100 per hour, on an average day, due to the fact she could do 2 - 3 clients per hour, then more than likely, you can bank on paying about this rate. Hopefully, you will only be in the chair for 1 hour or 1 1/2 hours, so I imagine $100 - $150 will be the… [cont.]
Answered by chelseiann - Sun Nov 18 23:38:36 2007
Q. I recently dyed my hair black and its naturally dirty blond. I wanna get it stripped but last time I did it myself it came out like 4 colors. Does anybody know about how much it cost for them to do it at a hair salon?
Asked by Lindsey J - Sun Nov 18 23:33:04 2007 - - 3 Answers - 0 Comments
A. This is corrective haircolor and it is the most expensive salon color service, due to the amount of time involved and the amount of products needed to fix the problem. This is the primary reason why you should have a hairdresser color your hair, so it doesn't come out in 4 different colors. It would cost you less to have that done vs corrective. Most hairdressers charge by the hour for corrective, because it can take a lot of time and products. If a hairdresser normally can make $75 - $100 per hour, on an average day, due to the fact she could do 2 - 3 clients per hour, then more than likely, you can bank on paying about this rate. Hopefully, you will only be in the chair for 1 hour or 1 1/2 hours, so I imagine $100 - $150 will be the… [cont.]
Answered by chelseiann - Sun Nov 18 23:38:36 2007
What to expect after having membranes stripped?
Q. I will be 40 weeks tomorrow and I had my membranes stripped today. I was not dialated at all. What can I expect over the next couple of days? I have had no discharge/show today following the stripping of my membranes.
Asked by Tiffany P - Tue Mar 16 18:40:52 2010 - - 3 Answers - 0 Comments
Q. I will be 40 weeks tomorrow and I had my membranes stripped today. I was not dialated at all. What can I expect over the next couple of days? I have had no discharge/show today following the stripping of my membranes.
Asked by Tiffany P - Tue Mar 16 18:40:52 2010 - - 3 Answers - 0 Comments
Advice on rethreading a stripped screw hole on transmission fluid pan?
Q. I have a 2001 Chevy Cavalier. I had been noticing occasional drips of tranny fluid in 3 evenly spaced increments beneath my car. After trying to replace the gasket and filter I realized the people who I had work on my car months ago had stripped 3 holes and had "jerry-rigged" it with loads of silicone. Now I am going to have to rethread the holes to a slightly larger size. Any advice or product recommendations?? Thanks in advance!
Asked by watershed_22 - Sat Feb 9 06:39:25 2008 - - 4 Answers - 0 Comments
A. i used to work on transmissions and i have had the problem you have many times the best way to fix it is with a heli coil, it replaces the threads that were there, your local auto parts store should have them
Answered by jay c - Sat Feb 9 06:48:17 2008
Q. I have a 2001 Chevy Cavalier. I had been noticing occasional drips of tranny fluid in 3 evenly spaced increments beneath my car. After trying to replace the gasket and filter I realized the people who I had work on my car months ago had stripped 3 holes and had "jerry-rigged" it with loads of silicone. Now I am going to have to rethread the holes to a slightly larger size. Any advice or product recommendations?? Thanks in advance!
Asked by watershed_22 - Sat Feb 9 06:39:25 2008 - - 4 Answers - 0 Comments
A. i used to work on transmissions and i have had the problem you have many times the best way to fix it is with a heli coil, it replaces the threads that were there, your local auto parts store should have them
Answered by jay c - Sat Feb 9 06:48:17 2008
How to get a stripped screw out from a yamaha raptor 660 throttle plate cover?
Q. My bf has tried everything to get the throttle plate cover off to clean the carburetor, but the screws are stripped from the previous owner. we have tried everything from the hammer and screwdriver to the drill. If you could help it would be greatly appreciated.
Asked by Cizzle13 - Fri Feb 5 16:35:11 2010 - - 1 Answers - 0 Comments
A.
Answered by Angela - Fri Feb 5 16:39:28 2010
Q. My bf has tried everything to get the throttle plate cover off to clean the carburetor, but the screws are stripped from the previous owner. we have tried everything from the hammer and screwdriver to the drill. If you could help it would be greatly appreciated.
Asked by Cizzle13 - Fri Feb 5 16:35:11 2010 - - 1 Answers - 0 Comments
A.
Answered by Angela - Fri Feb 5 16:39:28 2010
How long after the doctor stripped your membranes did you go into labor?
Q. I know I already asked this, but I only got 2 answers so I was hoping to get more this time. If you already answered, you dont need to answer again. Im getting my membranes stripped tuesday, and was curious how long it takes, does it hurt, and did it work for you and how soon. Thanks!
Asked by mandiliz06 - Tue May 8 16:37:47 2007 - - 4 Answers - 0 Comments
A. I had my membranes stripped on a wednesday. I didnt even really know he did it, it just felt like a normal pelvic exam. I had my son the next day.
Answered by Katie M - Tue May 8 16:46:25 2007
Q. I know I already asked this, but I only got 2 answers so I was hoping to get more this time. If you already answered, you dont need to answer again. Im getting my membranes stripped tuesday, and was curious how long it takes, does it hurt, and did it work for you and how soon. Thanks!
Asked by mandiliz06 - Tue May 8 16:37:47 2007 - - 4 Answers - 0 Comments
A. I had my membranes stripped on a wednesday. I didnt even really know he did it, it just felt like a normal pelvic exam. I had my son the next day.
Answered by Katie M - Tue May 8 16:46:25 2007
how do you get a stripped nut off of a battery terminal?
Q. I have a '96 sentra and am trying to remove the battery, but the nut on the positive terminal is stripped and seems almost to be fused to the bolt. I've already tried cleaning the terminals and oiling the nut and bolt, but the thing still won't turn. What do I do now?
Asked by jessica - Thu Sep 14 00:39:32 2006 - - 6 Answers - 0 Comments
A. put some liquid wrench on it and us vise grip. If you can get off with vise grips you can put chanel locks on the end of the vice grip for more leverage.
Answered by trailsman1961 - Thu Sep 14 00:43:06 2006
Q. I have a '96 sentra and am trying to remove the battery, but the nut on the positive terminal is stripped and seems almost to be fused to the bolt. I've already tried cleaning the terminals and oiling the nut and bolt, but the thing still won't turn. What do I do now?
Asked by jessica - Thu Sep 14 00:39:32 2006 - - 6 Answers - 0 Comments
A. put some liquid wrench on it and us vise grip. If you can get off with vise grips you can put chanel locks on the end of the vice grip for more leverage.
Answered by trailsman1961 - Thu Sep 14 00:43:06 2006
How do I fix a stripped screw hole in ceiling light fixture mounting bracket?
Q. My husband and I are trying to hang a chandelier in our nursery. We got everything assembled and ready to hang, hung the new mounting bracket that came with the chandelier, and found that one of the mouning screw holes in our ceiling (light fixure) box is stripped. How can this be repaired quickly? I would like to get this chandelier up by the weekend. the dome light that we are replacing is about 2lbs and the chandelier we are hanging weighs about 5lbs, if that makes a difference.
Asked by S. S - Sat Jan 23 02:31:22 2010 - - 5 Answers - 0 Comments
A. Put a self-taping screw through it.
Answered by Wp - Sat Jan 23 02:35:37 2010
Q. My husband and I are trying to hang a chandelier in our nursery. We got everything assembled and ready to hang, hung the new mounting bracket that came with the chandelier, and found that one of the mouning screw holes in our ceiling (light fixure) box is stripped. How can this be repaired quickly? I would like to get this chandelier up by the weekend. the dome light that we are replacing is about 2lbs and the chandelier we are hanging weighs about 5lbs, if that makes a difference.
Asked by S. S - Sat Jan 23 02:31:22 2010 - - 5 Answers - 0 Comments
A. Put a self-taping screw through it.
Answered by Wp - Sat Jan 23 02:35:37 2010
How Do I remove a stripped vaccum stopper on my outside water faucet?
Q. I have a metal vaccum stopper on my outdoor faucet and I do not know how to remove it for the screw is stripped. I have drilled out the screw and it still wont budge. I have tried lubricating it but it won't work.
Asked by LARDofthesea - Tue Jun 19 20:59:08 2007 - - 1 Answers - 0 Comments
A. Shut off water supply to faucet and replace the whole thing. Even if you get the stopper off, the threads will most likely be stripped .
Answered by jcarlp - Wed Jun 20 12:40:43 2007
Q. I have a metal vaccum stopper on my outdoor faucet and I do not know how to remove it for the screw is stripped. I have drilled out the screw and it still wont budge. I have tried lubricating it but it won't work.
Asked by LARDofthesea - Tue Jun 19 20:59:08 2007 - - 1 Answers - 0 Comments
A. Shut off water supply to faucet and replace the whole thing. Even if you get the stopper off, the threads will most likely be stripped .
Answered by jcarlp - Wed Jun 20 12:40:43 2007
How long does it take for stripped membranes to bring on labour?
Q. Mine were stripped about 46 hours ago and I am getting only Braxton Hicks. Also, I have no more blood (only for about 30 minutes).. does that mean it all closed up again? the Braxton Hicks are painful
Asked by mwa - Sat Jun 16 10:39:11 2007 - - 7 Answers - 0 Comments
A. Maybe hours, maybe days, maybe weeks. Membrane stripping doesn't always work; it didn't work twice for me, I didn't deliver until more than two weeks later. It doesn't "close up" though. Once the membranes are stripped, they are just pulled away from the uterine wall - they are not open or torn or anything - that would be rupturing of the membranes.
Answered by Jill - Sat Jun 16 10:49:16 2007
Q. Mine were stripped about 46 hours ago and I am getting only Braxton Hicks. Also, I have no more blood (only for about 30 minutes).. does that mean it all closed up again? the Braxton Hicks are painful
Asked by mwa - Sat Jun 16 10:39:11 2007 - - 7 Answers - 0 Comments
A. Maybe hours, maybe days, maybe weeks. Membrane stripping doesn't always work; it didn't work twice for me, I didn't deliver until more than two weeks later. It doesn't "close up" though. Once the membranes are stripped, they are just pulled away from the uterine wall - they are not open or torn or anything - that would be rupturing of the membranes.
Answered by Jill - Sat Jun 16 10:49:16 2007
Stripped the wallpaper and door frames. How to fix the underlying mess?
Q. We're remoldeling our 100+ yr old home. I've stripped wall paper and door frames. How do I fix the holes in plaster and smooth the walls before painting? Fiberglass mesh then joint compound or fix holes then joint compound? Whats the difference between the numbers on the compounds? I've seen 30, 45, and 90. How do I smooth the insides of the door frames, I'm down to the wooded framing. Do I cut down sheets of drywall or can I use the same technique as the walls?
Asked by Julie C - Fri Apr 4 10:03:54 2008 - - 2 Answers - 0 Comments
A. If the holes are shallow and not deep, then you should thin layer compound it, then mesh it and let it dry, then compound it again, let it dry and finally sand and paint it. As for the numbers, I am sure that has to do with the weight of the product. Some compounds are mixed with sand and weigh less and therefore dry faster. You can smooth wooded framing with a scrapper called sureform. As for the drywall, it depends on how much wall coverage your talking about...we recently cover our attic with very long sheets of drywall horizontally...it was more cost effective to do it this way.
Answered by Maria - Fri Apr 4 10:27:07 2008
Q. We're remoldeling our 100+ yr old home. I've stripped wall paper and door frames. How do I fix the holes in plaster and smooth the walls before painting? Fiberglass mesh then joint compound or fix holes then joint compound? Whats the difference between the numbers on the compounds? I've seen 30, 45, and 90. How do I smooth the insides of the door frames, I'm down to the wooded framing. Do I cut down sheets of drywall or can I use the same technique as the walls?
Asked by Julie C - Fri Apr 4 10:03:54 2008 - - 2 Answers - 0 Comments
A. If the holes are shallow and not deep, then you should thin layer compound it, then mesh it and let it dry, then compound it again, let it dry and finally sand and paint it. As for the numbers, I am sure that has to do with the weight of the product. Some compounds are mixed with sand and weigh less and therefore dry faster. You can smooth wooded framing with a scrapper called sureform. As for the drywall, it depends on how much wall coverage your talking about...we recently cover our attic with very long sheets of drywall horizontally...it was more cost effective to do it this way.
Answered by Maria - Fri Apr 4 10:27:07 2008
How do you remove a tiny stripped screw?
Q. I tried to remove a screw from my watch keychain to replace batteries and I accidentally stripped it. The screw is about 2 millimeters long and is still in the same spot as when I started. How can I get it out?
Asked by Ellie - Thu Nov 26 14:47:04 2009 - - 3 Answers - 0 Comments
A. Use a small, flat-head screw driver that JUST fits inside the largest groove. Use more force pushing down, than turning. That will prevent further stripping and should work. Obviously do not replace the damaged screw. Go to a jewelry store or Walmart and get a replacement.
Answered by Skyhawk - Thu Nov 26 14:51:49 2009
Q. I tried to remove a screw from my watch keychain to replace batteries and I accidentally stripped it. The screw is about 2 millimeters long and is still in the same spot as when I started. How can I get it out?
Asked by Ellie - Thu Nov 26 14:47:04 2009 - - 3 Answers - 0 Comments
A. Use a small, flat-head screw driver that JUST fits inside the largest groove. Use more force pushing down, than turning. That will prevent further stripping and should work. Obviously do not replace the damaged screw. Go to a jewelry store or Walmart and get a replacement.
Answered by Skyhawk - Thu Nov 26 14:51:49 2009
From Yahoo Answer Search: 'stripped'
Tue Sep 7 14:17:26 2010 [ refresh local cache ]
[Hide]▼
blogs.alternet.org
Sun, 22 Aug 2010 21:58:06 GMT+00:00
AlterNet (blog) Court martials should be held and officers who violated these d=soldiers fundamental constitutional rights should be stripped of their commands and given ...
livingindryden.org
533px x 800px | 158.30kB
[source page]
Front screen insert after paint stripping 5 18 2005
groups.drupal.org
Signal
hu, 12 Aug 2010 19:27:42 GM
I need to create an RSS feed that links to my current articles but not to the current pages, but to a . stripped. down version of the same article (without all the blocks, ads, and other content). The feed is going to be used for an iPhone ...
[Hide]▲
